Kubota SSV75 Specifications & Workshop Service Guide
The Kubota SSV75 is a skid steer loader produced during 2015-Present, powered by a 74.3-horsepower Kubota V3307-CR-TE4 Turbo Diesel diesel engine. It features an operating weight of 8,157 lbs (3,700 kg), a rated operating capacity of 2,690 lbs (1,220 kg, SAE J818), and an auxiliary hydraulic flow of 20.9 GPM at 3271 PSI (39.9 HHP).
Engine & Powertrain
- Engine Model
- Kubota V3307-CR-TE4 Turbo Diesel
- Gross Output
- 74.3 HP
- Crankcase Oil
- 11.6 qts (15W-40 CK-4 Low Ash)
- Cooling System
- 14.5 qts (50/50 Ethylene Glycol)
Hydraulic Circuit & Flow
- Auxiliary Flow
- 20.9 GPM (Standard Flow)
- Relief Pressure
- 3271 PSI
- Hydraulic HP
- 39.9 HHP (GPM × PSI / 1714)
- Reservoir Capacity
- 12.4 US Gal (Kubota Super UDT-2 Multi-Purpose Hydrostatic)
- Total System Vol
- 16.5 US Gal (Includes cylinders)
- Drive Chain Case
- 8.0 US Gal (SAE 10W-30 Motor Oil)
Wix / Donaldson OEM Filter Cross-Reference
Standard fluid and filter change requires exactly 12.4 US gallons to reach the center of the sight glass. Never overfill.
Hydraulic cylinders and lines hold approximately 4.1 US gallons. Total system capacity for dry rebuilds is 16.5 US gallons.
The chain case holds 8.0 US gallons of SAE 10W-30 Motor Oil. It is completely isolated from the hydraulic circuit.
Kubota SSV75 Technical Service Overview
Field service operations on the Kubota SSV75 require adherence to manufacturer hydraulic pressure relief tolerances (3271 PSI) and torque specifications. When performing standard 250-hour preventative maintenance, always verify hydraulic filter condition, check drive chain tension, and inspect high-pressure auxiliary couplers for mechanical wear or weeping seals.
Empirical Engineering & Statutory Verification Matrix
All tolerances and fluid formulas cross-checked against primary heavy machinery standards.
| Engineering Parameter | Authoritative Source | Authority Body | Factory Tolerance / Rule |
|---|---|---|---|
| Kubota SSV75 Rated Operating Capacity | SAE J818 Technical Specification Standard ↗ | 2,690 lbs (1,220 kg) | |
| Factory Service Manual Publication | Kubota SSV75 Skid Steer Workshop Manual WSM-9Y111-09420 | Verified Factory Documentation | |
| Hydraulic Reservoir Service Capacity | Kubota SSV75 Lubrication Specification Table | 12.4 US Gallons (Kubota Super UDT-2 Multi-Purpose Hydrostatic) | |
| Kubota V3307-CR-TE4 Turbo Diesel Engine Output | Engine Manufacturer Service & Workshop Data | 74.3 Gross HP (11.6 qts 15W-40 CK-4 Low Ash) |
Frequently Asked Technical Questions
Authoritative mechanical and operational answers verified against OEM shop manuals.
What is the rated operating capacity (ROC) of the Kubota SSV75?
Under SAE J818 standards (50% of tipping load for wheeled loaders or 35% for tracked loaders), the Kubota SSV75 has a Rated Operating Capacity of 2,690 lbs (1,220 kg). The static tipping load is 5,380 lbs (2,440 kg). Always operate within rated parameters to prevent rollover hazards.
What hydraulic fluid and reservoir capacity does the Kubota SSV75 use?
The Kubota SSV75 hydraulic reservoir requires 12.4 US gallons (46.9 Liters) of Kubota Super UDT-2 Multi-Purpose Hydrostatic. The complete system capacity with cylinders and coolers holds 16.5 US gallons.
What engine powers the Kubota SSV75 and what are the service intervals?
The Kubota SSV75 is powered by a Kubota V3307-CR-TE4 Turbo Diesel diesel producing 74.3 gross horsepower. The crankcase requires 11.6 quarts (11.0 Liters) of 15W-40 CK-4 Low Ash. Oil changes are recommended every 100 to 250 operating hours based on duty cycle.
Where is the serial number located on the Kubota SSV75?
Front upright plate beneath boom pivot.
What Wix filters fit the Kubota SSV75?
Primary cross-references for the Kubota SSV75 are: Engine Oil: Wix 57098 / Donaldson P550928; Hydraulic: Wix 57240 / Donaldson P568666; Fuel: Wix 33397 / Donaldson P550385; Outer Air: Wix 46562 / Donaldson P827653. Always verify thread pitch and seal diameter prior to spin-on installation.